car key repair company key fob repair Button repair car key remote

A damaged car key button is frustrating. It is possible to contact a 24-hour locksmith Service for assistance or to purchase a new remote.

But, you may be able to save money by repairing a worn-out key fob rather than replacing it. This is especially true when the issue is caused by the worn-out switch or defective contact.

Battery

If the buttons on your key fob aren't responding to pressing the buttons, that could be a indication that the battery is dying or nearing the end of its lifespan. Fortunately replacing the battery is an easy task that can be done on your own instead of hiring a locksmith to do it for you.

First, locate the battery compartment. This is usually found on the backside of the key fob and could be hidden behind the cover, which slides out, or an access point that opens when you press a button. When the compartment is open then you will find the small cell battery. This is typically shaped like coins and identified with an minus and plus sign. Remove the battery from the old one and put a brand new one in its place, making sure that the plus and minus marks are aligned correctly.

Close the compartment and snap together the two halves of your key fob. Before closing the door make sure to align and snap the parts in the correct position. Press any of the buttons to verify that they work properly.

If your remote keyfob still does not work after replacing the battery, there may be other problems that require a different type of repair key. Dropping the fob into a pool of water can cause it to stop working. It could also be due to a problem with the internal electrical system or the need to be deprogrammed. Take a look at these other car key button repair troubleshooting tips to see whether your key fob may be suffering from a different issue.

Switches

Depending on the year and the manufacturer, there are various types of switches that are used in the keyfob of your car. The older style key has a chip that is visible inside the case. The latest keys operate by transmitting signals to your car. No matter what type of key, the keys' buttons can become worn out or damaged when used regularly. They can become difficult to press or unresponsive. If you try to force the button to function it could cause further damage and potentially stop the key from starting your vehicle in the future.

If your key doesn't seem to be working, you should first try changing the battery. If this doesn't work, you might need to clean your key's fob or adjust its switches. Because these tiny electronic switches are constantly getting jostled around and tangled, they are more likely to wear out than larger components of your key.

The switches have a rubbery feeling and are coated with an electrical conductor. The film may be worn away over time. Fortunately, they're tiny and affordable to replace. The old ones are soldered to the circuit board, so you will need to carefully remove them without damaging anything else. Then, you can solder the new ones into and reassemble your fob.

An effective way to protect your car key fob from becoming ruined is to avoid using it for more than a few hours at a stretch, and also to not leave it in places that it will be visible. Also, you should locate a safe place to keep your key in when you're not making use of it.

If the problem persists after you have cleaned your key fob replaced the battery and attempted to clean it, you may need to consult a locksmith. A professional can check the frequency of your key to determine if it's still able to communicate with your vehicle, open and replace micro switches, change cases and much more.

Outer Case

Key fobs spend many hours bouncing around, and when the buttons aren't allowed to move up and down within the case, they could become stuck or even broken. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it may be necessary to remove the case. If the contact points Where to repair Car key remote the buttons touch aren't fitting well or are worn out, adjusting them could be the only way to correct the issue.

Rubber buttons can wear out over the years. The rubber expands, nails gouge into it, and the buttons become difficult to press. This could cause the key to fail and, in this situation, it is time for a new case or new buttons. This repair involves disassembling your remote, looking for the buttons on the board, then heating the solder, and carefully remove them. The circuit board is soldered with new buttons. The case can be reassembled and the key blade of the horseshoe can be attached. The new buttons should be tightly fitted into the case in order to prevent them falling out.

Inner Case

Over time, your key fob's buttons may be damaged or stuck as a result of the continuous rubbing and accidental pressing. If your key fob stops working when you're away from home It is possible to solve the issue quickly using metallic tape and a punch hole. This will allow you to unlock doors but not start your vehicle. This simple fix can enable you to safely make it back to your vehicle and finish your trip.