Patio Door Lock Repairs

Over time, patio glass door repair near me doors experience wear and tear that can lead to locks that fail. However, there are simple and efficient ways to restore your uPVC patio door's security.

These simple fixes will make your home safer no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Patio doors are ideal for letting the outdoors in while keeping out the elements. However they can pose an issue for security if the lock doesn't work properly. Over time, wear and tear, cold and hot weather dirt and debris can cause your patio doors repair near me door lock to become difficult to operate. With a little maintenance, you can ensure your patio door's locks will always perform correctly.

It's essential to clean the lock of your patio doors repairs door and all the moving parts. This will help remove any dirt or coatings that might be hindering your lock from working properly. Start by wiping down the moving parts of your patio door's lock using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub any difficult-to-access areas of the door and frame that are covered in dirt. It is recommended to wipe the entire lock with dry cloth to get rid of any remaining dampness and allow it to air dry prior to making use of it again.

If you have a patio door that uses a pin tumbler latch mechanism You can grease the lock by applying graphite powdered to the key or using a lubricant made of Teflon, such as WD-40 Multi-Use Product. This type of lubricant can be easy to apply and it won't disintegrate over time. If you're unable to find the right lubricant for your lock, make use of a pencil with a more of a thicker tip. Place the pencil in the lock and move it around a bit to spread the graphite.

Tracks for sliding patio doors require regular maintenance to keep them free of dirt, dust, and debris. They are particularly susceptible to snow and ice, which could cause them to become stuck or slack and make it difficult for your patio doors to open and close.

Sliding patio door track rails and rollers can be cleaned by removing weather stripping that is damaged or dirty and then cleaning it, before replacing it. The same is true to emergency patio door repair door rollers which can be cleaned and sprayed with non-stick lubricant in order to allow them to move freely.

Lubricate the moving parts

uPVC french doors, which are similar to sliding patio doors, work using 3-4 or sometimes five-point locking mechanisms, which include the lock cylinder and handle controlled by the key. These doors require maintenance, the lubrication of moving parts. This can be accomplished with a thin oil but not WD40. It is recommended to do it at least once per year.

If sagging hinges aren't the cause, the door could be misaligned and caught or rubbing against the strike plate's hole in the frame. The solution is to remove the strike plate, and then use a sharp chisel to enlarge the mortise that it rests in. This allows the latch to sit perfectly in the hole and avoids rubbing or catching on the frame.

While the cylinder is out of the way and out of the way, measure its width using a book or piece of wood that fits into the adjustment screw gap above the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner dimension extends from the center of the adjustment screw to the end of the cylinder.

Verify the lock's width

If your patio door latch isn't able to turn, even after cleaning and lubricating, there's a possibility that it's not in alignment with the strike plate hole. Check if your door is balanced, and that the hinge screws are tight. In most instances, moving the strike plate downwards or upwards could fix the problem.

Oftentimes, the problem occurs when the strike of the lock is too small for the latch to properly engage. In this instance you'll need to expand the opening using the hammer or chisel and then test the latch to ensure that it is able to engage the strike plate without rubbing against or getting caught on the door's frame jamb.

You should identify the type mortise lock you are using before you purchase a replacement. This can be done by looking at the faceplate on the lock and noting if it is square or round. Then, look at the screw holes on the current lock and note the dimensions of each. This will aid you in finding an alternative that is the same width and fits perfectly into the hole you have already.

In addition to identifying the current mortise lock you should also examine it for any nicks or bends that may require repairing. A damaged or bent latch is more likely than one that has frequently used to break. Replace the lock if it displays indications of damage.

After you've determined the type of lock replacement you need Now it's time to start the actual repair. Remove the handle and spindle from the patio door, and then install the new one. Begin by installing the handle in the interior, aligning it with the spindle, and then securing it in place with the two bolts or screws that secure it. Once the interior handle is installed, you can install the handle that is outside and screw it in place as well. After you've completed the steps, you can test the new handles to ensure that they are able to open and close with ease and that the latch catches properly with the strike plate.

Check the Strike on the door.

The door latch and strike plate are the two components of the lock that work to ensure that the latch is secure the door. A misaligned strike plate or door latches will result in the latch not being able to latch the door correctly. This issue is usually easy to fix.

First, examine the holes in the strike plate's receiving to make sure they are clear of obstructions like dirt or plastic plugs. Then loosen the screws that hold the strike plate in place, allowing it to move horizontally, but not removing it from the door frame. Then, adjust the strike plate to ensure that its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted tighten the screws, and then test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio door repair doors. However, they are essential to lock and unlock your door. The metal plates are situated on the top and bottom jambs of your door, where they support its latch. The door latch is inserted into the strike plate, and it creates an airtight seal. If the strike plate has been damaged or rusted or not properly installed the latch may not properly lock the door.

A misalignment between the latch and strike plate is the most common reason for the patio lock not to close or remain in place. This can be verified using the "lipstick" test. Rub some lipstick on the outside of the deadbolt and then cover it with masking tape. The lipstick will leave a mark when you shut the door. This will reveal exactly where the latch meets the strike plate. If the mark is too low or high, you can easily alter the strike plate.

Sliding patio door locks help keep your home safe from intruders, and if they're not functioning correctly, you should fix the problem quickly. Follow these easy steps to fix your patio door lock and restore it's function.