seat alhambra key programming Alhambra Key Problems

Seat's jumbo MPV family is among the top models in its class when it comes down to resales values. With a new model on sale, the jumbo family MPV is even more impressive.

There are a myriad of reasons the key fob might not work as expected, including an unresponsive coin battery water damage to the receiver module, or signal interference. This article will guide you through the steps necessary to make sure it works.

Water Damage

If your key fob for the seat spare key alhambra survives an wash cycle or dip in the ocean or a pool then it's got a waterproof chip. But don't do this often, as prolonged exposure to water increases chances of the key fob getting damaged. If your key fob stops functioning after being exposed to rain or clean tap water, remove the battery and clean the electronic component with a paper towel. Allow it to dry completely before replacing the battery. If the key fob was exposed to salty or soapy water it is recommended that you clean the chip with isopropyl or electronic cleaner.

Faulty Receiver Module

If you've tried a new battery for a button and the key fob still isn't locked or unlocking, it is likely that the receiver module has been faulty. The good news is that this is a simple and inexpensive repair, you can disconnect the battery for a few minutes (first remove the negative cable then press the horn button several times) to remove any remaining electricity, and then connect it in reverse order e.g. Positive first, then negative.

ESP Warning Light - If the ESP warning light flashes, it is normal and signifies that the car is traveling over terrain that has traction issues between the road surface and the tyres isn't ideal, such as gravel, snow or lots of surface water. If the ESP warning light remains shining, it is a sign that there is an error within the system. It should be detected with a iCarsoft i908 Seat Keys Replacement OBD Code Reader kit that will give you a specific fault description.

Dead Coin Battery

One of the most common reasons for the seat arona key cover alhambra keys to stop working is a dead battery. The key fob is powered by an insignificant button cell battery which keeps it powered. Replace it with a brand new battery with the same voltage, size and specification as the original. When replacing the battery on the key fob, remove all metal clips and ensure that the contacts of the key fob are clean and free of corrosion.

If the key fob was exposed to water, such as soapy or rain it is recommended to remove the battery and clean the electronic chip with isopropyl alcohol or a electronic cleaner before putting in the new battery. The chip may be permanently damaged by moisture. If the key fob still not working after replacing the battery, it may be necessary to replace the entire key fob.

Faulty Receiver Module

If your key fob stopped working after replacing the battery, but it didn't function, or stopped working abruptly your receiver module might have encountered a problem. The receiver module receives radio frequency signals from the remote keyfob and transforms them into electrical signals that are then processed by other modules within the car.

If the receiver module has developed a fault and is unable to respond to any of the commands sent by your remote key fob. In this scenario, you will need to go to a dealer to reprogram the key fob, and also a new receiver module.

The key fob has rubber seals that stop water from getting into the electronic chip inside. If you dip the key fob into salted or soapy water it could cause damage to the chip. If your key fob does not function, you can try cleaning the chip using isopropyl or electronic cleaner.

If the keys are linked, but the receiver module is not working You can try to restart all of the electronics on board by disconnecting the battery that is 12 volts for a few minutes. Then reconnect the battery in reverse order (negative cable first followed by positive). This will reset the onboard electronic and restore their functionality.

Faulty Electronic Chip

The key fob is fitted with a tiny chip which transmits an indication from the key to the receiver module every time the key is used. If this signal does not match the one recorded by the car the immobilizer will shut down the engine and prevent the vehicle from starting. If the key fob won't work and you aren't able to reprogram it, this could be due to a faulty microchip.

The chip inside the key fob might need to be altered to make it work again. The best method to do this is by removing the key from its housing and then using a pin needle to connect with each of the metal retaining clips. If the clips are corroded, or broken, you will require replacement in order for the remote control to function. Make sure that the replacement batteries are the same size, voltage, and specifications as the original.

Seat Alhambra, a popular and well-designed car, can be a bit troublesome with certain components or equipment. Some owners have reported issues with the automatic climate-control system. It could malfunction and be stuck in a particular setting. The infotainment system may also fail and cause freezing of the screens.