how to repair broken car key to repair car remote control key car keys (Atavi.com)

The car keys aren't big and might not seem to be important, but they are essential for the operation of your vehicle. The cost of replacing a traditional or modern transponder car keys can be upwards to $200.

There are solutions to fix your car keys yourself for less than the cost. This article will go over some of the most frequent car key problems and their DIY solutions.

Dead Key Fob Batteries

Cars are equipped with remote key fobs which makes opening doors and trunk easier than ever before. However, the battery in the device could die. Fortunately, there are some techniques that can be employed to resolve this issue in the event of a need.

First, determine if the car is still in ignition mode. If it is, then the battery on the key fob could simply be low instead of dead. To test this, push the button on the key fob right up against the vehicle's ignition button. If it works, the battery is probably fine and has to be replaced.

To replace the battery within the fob, pry open the case using an screwdriver. Do not apply too much force as this may cause the fob's case to split. If the fob isn't opening easily, try putting your pry tool in more than one place on the outside of the case.

Once the fob is open, remove the mechanical key, and then open the electronic part of the car. Install the new battery and snap it back into the shell. If your key fob does not work after this, it may be due to an problem with the remote starting system in your car. This will require an expert to identify. A reputable mechanic will capable of helping you in this situation. If you need help with your car, you can contact roadside assistance.

Broken Key Ring

There are a few steps that you can do when your key fob does not function because the ring is broken. Look to see if can locate the broken piece inside the ignition. If it is, remove it without damaging the lock on the ignition or door lock. If you have trouble removing it, call a locksmith for help. They have special tools that can safely remove the damaged key from the ignition.

Another reason that can lead to a broken car key is the corrosion of the circuit board or plastic frame. You can clean the circuit board using rubbing alcohol and a cotton swab. This will eliminate the corrosion and protect to the contact pads.

If your key isn't working because the ring is broken, you may be able to repair it by using a thick wire or nail to close the hole. Superglue can be used to repair keys near me damaged key rings. First, clean the damaged rings with a damp cloth and then apply a small amount superglue to the ends of the wire or nail. Apply the glue to the ring and let them dry prior to using your car. These DIY solutions may seem appealing, but they are only temporary solutions. For long-term repairs, you'll want to get an expert locksmith. They have the tools and knowledge to fix a broken car key remote repair near me key quickly and effectively. They can replace the battery and reprogram your key fob, if needed.

Broken Key Blade

Some key blades may break due to wear and tear. If this happens, you should probably purchase a new one. The issue isn't as serious as you might believe at first. The problem is that the metal blade has snapped away from the case.

One solution is to spray the key hole with a oil-based lubricant. You can then use pliers or tweezers to grasp the damaged end of the key and pull it. If the key is magnetic, you can also use a magnet to help pull it out. Use a magnet to help you remove the key, but be cautious to not break the tumbler of the lock.

Contact a locksmith immediately when you are unable remove the broken piece of the key. They have special tools that allow them to safely remove keys without causing damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of the glue to the edges and press them in. After that, wait until the glue is dry before you insert your key into the lock. This method isn't very reliable, and you may need to repeat the process several times before it is successful. Plus the super glue may not be enough to keep the key in place. This is more of a temporary solution rather than a permanent solution.

Broken Plastic Loop

If your key fob's plastic loop gets damaged it could render the key ineffective. Luckily, this is an easy fix. You can use wire or a nail for finishing as a replacement. Make two holes in the damaged loop of plastic for each end of the wire or nail. Cut the wire or nail into a key width, then place a small drop of superglue in each hole. Apply the nail or wire into the holes and let them dry.

A locksmith who sells replacement shells is another option. They can remove the programmable portion of your key, move it to the new shell, and cut a new blade for much less than a complete replacement cost.

It's not the ideal solution, but it'll bring you back on the road in case your key broke in half. It's not easy to fix when the blade of the key is in the ignition, however. If you're not cautious you can use a hair clip or needle to remove the broken part from the ignition. The best choice is to contact a locksmith with special tools for safely removing broken keys from the ignition. They can also create new keys with the proper cuts for your ignition, so it will work properly when it is inserted into the lock.

Broken Master Key

You'll have to attempt to retrieve the key before it becomes completely destroyed. You can employ the tweezers, lubricants and needle nose pliers to grab the broken fragment of a key.

Spray the inside of your lock with WD-40 or a graphite powder. You can also try the hacksaw blade method, which involves gently sliding the blade along the edge of the broken key and hooking onto some of the teeth - if you are able to do this, you should be able take the broken key from the lock.

Many hardware stores sell the spiral key extraction tool. It is a thin, flexible bar with spiral threads, which can be put into the keyway, and then bent to reach into the damaged section of the key. Once it is hooked to the serrations, it is possible to twist it in a circular motion and push it against the damaged portion of the key to take it out.

Before calling a locksmith, try to get rid of the broken master key. If you're unable to take the broken piece off then you'll have to contact a professional locksmith. A locksmith can give you an entirely new key that will be programmed with your car transponder.