How to Change a Subaru Spare Key

Contact a locksmith if lose your Subaru key. Usually, they will cut keys for you much less expensively than the dealer.

Fob remote "push to start" intelligent keys or a plain metal key are the two most popular kinds of Subaru car keys. The Fob keys have an embedded chip and must be reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. The remotes use the keypad in your car to connect with your computer system inside the vehicle.

Subaru models come with a lesser known feature called PIN Code Access. This allows you to use a personalised number sequence to start and open your car. If you own a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that came with this feature, refer to the owner's manual for instructions on how to program subaru key to utilize it.

If your keys stop working, there's a good chance that the battery in the key fob is dead. The first thing you'll want to do is make sure that it's got new batteries, and you can do this with a small remote tester or an ordinary multimeter in your garage.

The next step is to take the circuit board for the transmitter from the key fob, and then look at it. There will be one or two 8-digit sets. Note down the first set so you can remember it. Once you've finished then put the key fob back together and you'll be able to begin programming it at home. The procedure for programming will vary based on the type and year of your car but it's usually easy enough to accomplish yourself.

Key Fobs

Subaru's latest models come with key fobs that don't just unlock the doors but also activate your lights, lock the gas cap, and start your vehicle. This feature is especially useful if encountered yourself at the gas station and your car wouldn't even start because the battery inside the key fob has died.

It's likely that your subaru key programmer lost keys (Dokuwiki.Stream)'s key fob, regardless of whether it's brand new or old, can be easily replaced. It's important to note that the most recent models that have an advanced level of technological sophistication could require an outing to the dealer. With a little time and effort, you'll have your replacement key fob in place at home.

Begin by looking at the transmitter circuit board inside your key fob (instructions to open the case must be included in the owner's guide). There should be two or more serial numbers that have 8 digits each. Write down the first number series and save it to refer to later.

Then, sit in the driver's seat, and close all of the doors. Turn the key 10 times to start your car, then switch off the engine. Press the lock button on your key fob, then open the door. This will confirm that your doors are working properly. Close the door, and then take the key off. The car should chime again, indicating that the key fob is programmed.

Ignition System

The key battery could be dead if your Subaru keys aren't working as they should. If you are aware of the issue, you can replace the key fob's battery yourself. A replacement subaru key fob battery is not expensive and is fairly easy to locate. If the key fob isn't responding to your commands there could be a different issue. It's best to visit a dealership to purchase a spare key. They'll ensure that the key is genuine Subaru key that's under warranty and will be programmed to your vehicle. This is far more secure and less expensive than purchasing an aftermarket key from a company online.

The dealer will also cut keys for you if you give them your VIN number as well as evidence of ownership. They'll use this information to code the replacement key so that it can be accepted by your immobilizer. This procedure is more complicated than simply cutting a new one, and the dealer will generally charge more for this service.

Once the new key is programmed, you can switch it with your working key. It takes just five seconds to insert the new key, so keep your working key close to the ready. You can take the key off when the security light has stopped flashing and you can test it.

Battery Replacement

Subaru fobs are very beneficial because they can switch on the power windows and sunroofs of your vehicle with a single button press. The battery in your subaru legacy replacement key fob isn't designed to last forever, and will require replacement at some point. This quick guide from Capitol Subaru will help you to replace the battery on your own.

You'll have to find the small crevice that is the gap between the front and back of your keyfob. Utilizing a small flathead screwdriver, you'll be able to pop this seam open to reveal a small area inside that houses the battery. Remove the old battery and then insert a new one, ensuring that it is facing the correct side up. Once everything is assembled and you are able to use your new key fob to lock, unlock, and start your vehicle effortlessly!

Always have a spare set keys, particularly if the one you have is damaged or lost. A new key can easily be purchased at your local dealership for cars or you can get one made by an locksmith. Either way, it's important to get your key fob working correctly in the shortest time possible to ensure you drive safely!