Replacing uPVC Window Handles

Changing upvc window handles is an easy task. It is crucial to ensure that the replacement handle fits inside the spindle cutout in the window mechanism.

If the steps below are followed, any cockspur handle should fit most windows. The height of the step of the handle is crucial.

What to Look For

Over time, uPVC handles on many windows in the UK may begin to show signs wear and tear. When this happens, the window handle could become shaky or difficult to operate, making it necessary to replace it. Anyone who is familiar working with basic hand tools can accomplish this fairly simple task.

The first step is to make sure the handle is firmly connected to the window frame and in an open position. The next step is to find the pins or screws that secure the handle. These are usually located on the inside of the handle. They can be removed using an screwdriver or pliers.

When the handle has become loose It is best to gently pull it away from its hinges. Then, you will need to find a new handle that is the same dimensions and style. This can be accomplished online or in an area DIY store, and it should take about five minutes with an screwdriver.

The most important thing to consider when replacing the uPVC window handle is its step height. This is the distance from the base of the handle to the point at which it is placed on the window frame. This is usually an average measurement, but it is essential that you examine the step height of your current handle before ordering an entirely new one.

There are a variety of sizes based on the type of handle. Inline handles are offered for uPVC windows that have lug centres of 31mm, while cockspur handles have centers of lugs of 43mm. Tilt-and-turn handles are commonly found on uPVC windows. They have a specific design that lets the window be tilted for ventilation, and then turned to fully open the window.

The most frequent uPVC handle breakage is internal cracking, rather than a breakage from the base. This could make it difficult to open. It is essential to ensure that any replacement handle has the same spindle as the original one.

Remove the Old Handle

If the handles on your windows are damaged or improperly installed, they could cause double glazing door handles-glazed windows to open and close incorrectly. They may even get stuck. This can be caused by various factors, such as general wear and tear on the handle or corrosion. In these cases it is essential to locate replacement handles made of upvc immediately to prevent further damage and loss of function.

When replacing upvc windows handles (what is it worth) it is recommended to remove the handles that were previously installed from the window. Start by removing the screw with the handle when it is in a closed position. This should reveal another screw that once removed, you can then begin to remove the handle. It is a good idea to employ an electric screwdriver to accomplish this, as it makes the task much easier and quicker.

Be aware that screws could be hidden in caps made of plastic. It is best to remove the covers with the help of a Stanley knife. After the old handle has been removed, you should then look at the square cut on the handle's base to make sure that the new window lock handles will work with it. This is crucial as you'll need to measure the length of the spindle on the old upvc door handles handle to ensure that it is the same size as the window mechanism and handle spindle cut out.

The different types of window handles made of upvc are: Espag handles, which are equipped with a central screw and will turn left or right; Cranked handles, with two screws, and are typically found on tilt and turn upvc windows and Spade handles that have an arm that is flat and can be put on either side of the window. Once you have a suitable replacement, it is just a matter of screwing the handle in place and making sure that the spindle is correctly placed into the lock mechanism. After that, you can then tighten the handle to the window frame. The new upvc handles should now be secured.

Take a measurement of the Spindle

If you're replacing a upvc window handle that has fallen off, it is likely because the spindle holding it in place has become damaged or loose. In certain situations it is possible to tighten the spindle by using a screw or pin. In some instances it is necessary to replace the handle. There are several different types of upvc handles. They include espagnolette handles inline, cockspur handles, and tilt and turn handles. Each handle type has its own procedure for installing and replacing the handle.

Before buying a replacement handle it is essential to know the size of the handle that is currently in use. This will ensure that the new handle is the correct size and will fit correctly into the window. All handles are calibrated in accordance with industry standards, so it is easy to identify the correct size.

To determine the size of the handle move the window to the open position. You should be able see the size of the screw or pin that secures the handle. Make use of a ruler or tape measure to determine how long the spindle is. Once you know the length of the spindle, you can purchase a replacement spindle that is the same length.

The step height of a window handle is another factor to take into consideration when you are buying an alternative. The step height is measured from the base to the point where the handle sits on the frame. Typically, this is around 21mm for uPVC windows, and 9mm for aluminum. Dropping something in the gap will let you see how far the handle extends before it comes into contact with an obstruction.

Cockspur handles can have different backsets, based on the style of window you install them in. Inline Espag handles have the standard height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets depending on which window design they are placed in. This is due to the fact that they have a spur that extends from the handle and locks onto a cockspur wedge hitting plate.

Fit the New Handle

After you've chosen the new handle, make sure it is aligned with the screw holes on the door handles. Secure it using the screws provided. Install the latch lever the same manner as the handle that you are replacing if you are also replacing the door handle. After that, attach the patio door handle replacement trim again to conceal the screws for mounting.

Tips: To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the ground. Then use an hammer and tap the thin end. Be careful not to damage the handle or spindle.