Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the fiat punto remote key price 500 allows you to easily open doors and start your car. There are a myriad of reasons the key fob might stop working. It could be due to a dead battery damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement Fiat panda key Flip Key Remote - similar to the Ilco brand that needs how to start a fiat 500x with key be programmed professionally by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is due to a dead battery. Modern key fobs offer an operating range that is limited and must be within a few inches of the vehicle in order to function. If you're far from your vehicle, and you press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the coin cell battery (Part number CR2032) with a brand new one from a reputable brand like Panasonic, Duracell, or Energizer. You can usually find them in your local hardware store, or online.

After you've replaced the battery in the coin cell, you can test it by standing next to your fiat 500 replacement key 500 and pressing the buttons. The car should flash its parking lights, and the key fob should work the lock and unlock switches.

If your key fob still isn't working after replacing the battery, there may be water damage which has prevented it from interacting with the module in your vehicle. Water damage can occur in a variety of ways, ranging from an accidental splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, place it in a bag of rice to draw out the moisture. If this does not work, you'll need to have the fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually end up dying. If you get the fob wet, it's not an ideal choice, but if you drop it in an empty cup of water, or fail to remove it from your pants pocket before running the washer Don't give up hope.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it thoroughly before replacing the battery. Then try the fob and see if it works. If the key isn't working then it might need to be programmed again. This is usually handled by a professional or dealer auto locksmith.

If your key is a bit older and is not programmed for your vehicle You will need to replace it completely. This is a straightforward process that can be carried out by a professional automotive locksmith. The locksmith will require the key to be cut to match the car's ignition. They'll also have to reprogram the fob for the system of your car. It's a simple and inexpensive process that can usually be completed within the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote has a maximum range of 30 feet. Therefore, if you are too far from your vehicle it won't be able to respond to your commands. It is possible to solve this problem by moving the remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. Reprogramming the fob typically resolves the issue. You can find the instructions for most vehicles on YouTube or in the owner's guide.

It is sometimes necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension they could stop the battery from being properly seated, and this will cause the remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle due to software or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases it may be necessary to reinstall the program in your body control module too.

Interference

In addition to a dead battery on a coin The key fob may not be able to transmit or receive signals due to interference. This could occur if the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob may not function include a weak connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then interpreted by the vehicle.

Fortunately, there's an easy way to reset all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electrical charge, and then restart the computer of your car. This can help you get your key fob to work again. If the problem persists you should seek out an expert technician. They will be able to determine the exact cause of any issues.